Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Blog Article
They are making a number of great points regarding Installing A Bathtub in general in this content beneath.
Setting up a tub isn't specifically brain surgery, yet it does call for strong plumbing, carpentry, and sometimes, tiling skills. Replacing an old bathtub with a new one is likewise a moderately challenging job. If the old bathtub is easily available, the job can relocate speedily; if you have to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will need a helper to move out the old tub and embeded in the brand-new one. See to it you have actually certified on your own for the task as well as are comfortable attempting it. Rather than working with a specialist to take control of a halfway-completed job, it is better to take into consideration utilizing one before you begin. Opportunities are you might need a specialist plumber to make tube links.
This short article will aid you set up a brand-new tub in your restroom if you have currently acquired a brand-new tub and do not require to alter the arrangement of your previous water pipelines.
Your tools and also material checklist need to make up the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is disconnect the water. After doing so, activate the taps to drain any water continuing to be in the system. The process of removing the existing taps can be fairly problematic due to the limited accessibility that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from turning throughout this process. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old sealing compound.
Prior to carrying on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin guaranteeing that the washers are in area in between the faucet and also the sink. Safeguard the faucet in position with the maker offered backnut. When the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal tap connectors. The previous kind must be linked to the tap ends initially, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Bathtub
Using the two wood boards under its feet, position the bath tub in the required position. The wood boards are useful in evenly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny points.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bath tub till the level reviews degree.
To mount taps, fit the bottom of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water and also examine all joints and also brand-new pipework for leakages and also tighten them if needed. Fill up the tub as well as likewise inspect the overflow outlet and the normal outlet for leaks.
Ultimately, deal with the bathroom paneling as defined in the maker's instruction manual. Tiling as well as sealing around the bathtub needs to wait till the bath tub has actually been utilized a minimum of once as this will resolve it right into its final setting.
Preparing for the Installation
To start with, the sustaining framework supplied with the bath needs to be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps unit to stop stress on the bathtub.
Fit the adaptable faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you make use of every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last setting.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack an inflexible seal, causing the water to pass through the wall in between the bath and also the tiling, resulting in complications with moisture and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes and cartridges, as well as are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked paper or soft rope. Bear in mind to constantly fill the tub with water prior to sealing, to permit the movement experienced when the bathtub is in use. The sealer can crack relatively very early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily available on the market. It is recommended to fit the ceramic tiles making use of waterproof or waterproof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our section on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks so much for taking the time to browse our article post. Liked our write-up? Please share it. Help another person find it. Many thanks for taking the time to read it.
Details Report this page